POINT-TO-POINT WORKSTATION I O Reference Manual

HP 2392A 

DIRECT CONNECTION, CHARACTER MODE 

MPE I/O CONFIGURATION 

     Device Name:          ATP, ATP37      HPTERMATP
       (MPE G.01.00
        or Later)          ADCC            HPTERMADCC

     Device Type:          16

     Subtype:              ATP             0

                           ATP37           0

                           ADCC(HIOTERM2)  0

                           ADCC(HIOTERM0)  0, 4

                           ATC             0, 4

     Terminal Type:        10 Standard for HP CRT terminals

                           18  For XON/XOFF protocol

MODE SELECTIONS 

     Line Modify           OFF (no asterisk in label)

     Modify all            OFF (no asterisk in label)

     Block Mode            OFF (no asterisk in label)

     Remote Mode           ON  (asterisk in label)

     Smooth Scroll         OFF (no asterisk in label)

     Memory Lock           OFF (no asterisk in label)

     Display Functions     OFF (no asterisk in label)

     Auto LF               OFF (no asterisk in label)

TERMINAL CONFIGURATION 

     Datacomm/Ext Dev      Port 1/Port 2 (Not present if PORT2 not installed)

     Keyboard              USASCII

     Terminal Id           2392A

     Language              English

     Local Echo            Off

     Caps Lock             Off  *

     Start Column          01   *

     Bell                  On   *

     XmitFnctn(A)          No

     SPOW(B)               No   *

     InhEolWrp(C)          No   *

     Line/Page(D)          Line

     InhHndShk(G)          No

     InhDC2(H)             No

     Esc Xfer(N)           No   *

     Field Separator       US ([[CONTROL]]_)

     Block Terminator      RS ([[CONTROL]]^)

     RETURN Def            CR ([[CONTROL]]M)

     TermMode              HP

DATACOMM CONFIGURATION 

     ATP or ATP37 

     Baud Rate             300, 600, 1200, 2400, 4800, 9600, 19200

     Parity/Data Bits      NONE/8, 0's/7
     EnqAck                YES

     Asterisk              Off

     Check Parity          NO

     SR(CH)                Lo

     RecvPace              Terminal Type 10:  None
                           Terminal Type 18:  Xon/Xoff

     XmitPace              None

     CS(CB)Xmit            No

     ADCC(HIOTERM2) 

     Baud Rate             300, 600, 1200, 2400, 4800, 9600

Other settings same as ATP.

     ADCC(HIOTERM0) 

     Baud Rate
       Speed-sensed:       300, 1200, 2400
       Speed-specified:    300, 600, 1200, 2400, 4800, 9600

Other settings same as ATP.

     ATC 

     Baud Rate             110, 150, 300, 600, 1200, 2400

     Parity                NONE, ODD, EVEN

     Check Parity          No parity:               NO
                           ODD or EVEN parity:      YES

     Other settings same as ATP.

DIRECT CONNECTION, PAGE BLOCK MODE 

Strap Settings and Block Mode may be changed programmatically.

MODE SELECTIONS 

     Block Mode            ON   (asterisk in label)

TERMINAL CONFIGURATION 

     Line/Page(D)          Page

     InhHndShk(G)          Yes

     InhDC2(H)             No

MODEM CONNECTION 

MPE I/O CONFIGURATION 

     Subtype:              ATP             1
                           ATP37           1

                           ADCC(HIOTERM2)  1

                           ADCC(HIOTERM0)  1, 5

                           ATC             1, 5


NOTE  Hewlett-Packard does not support the use of half duplex modems.


DATACOMM CONFIGURATION 

Baud Rate selected must be supported by terminal, controller, and modem.
Refer to rates shown above and in the Table 12-7, Recommended
Asynchronous Full Duplex Modems, for possibilities.

     CS(CB) Transmitting            Yes (1)
     Depends on type of modem used

Other configuration settings are the same as for direct connection.